⚠️ Do not disassemble, incinerate or short circuit. You will jeopardise the water proofing.
⚠️ Do not expose to temperatures higher than 60°C/140°F.
⚠️ Charge only with specified charging cable.
⚠️ Expose a POCA audio product to salt water.
⚠️ Drop, strike or use a POCA audio product to hit any other object.

Accessories:

⚠️ Overtighten the speaker to any accessory. The speaker should be screwed on hand-tight, but not loose.
⚠️ Attach any other device to an accessory, except a POCA audio approved product.
⚠️ Position an accessory where the attached speaker could be struck.
⚠️ Force or lever your speaker while attached to an accessory.
⚠️ Attach a POCA audio product to a moving vehicle. A car is a no-no, a paddleboard is OK!

*Failure to follow the enclosed warnings may result in product damage and void the warranty. Please refer to our Warranty Policy for more information.

To turn on

1. Press and hold the 🔘 Power button for 2 seconds.
2. You’ll hear a Forest Heartbeat chime and the LED will flash white.

To turn off

1. Press and hold the 🔘 Power button for 2 seconds.
2. You’ll hear a Glacial Ice chime and the LED will turn off.

First-time pairing

1. Make sure your PINE Beat is on. It will automatically go into pairing mode.
2. On your phone, open Bluetooth settings.
3. Look for PINE Beat and tap to connect.
   You’ll hear a Glacial Ice chime when successfully paired.
   

From now on, it’ll reconnect automatically.

Pair a new device

Hold the Play button for 2 seconds to enter pairing mode. Follow the steps above.

Use only the included USB-C cable (5V at 2.4A).
For faster charging, use a USB-C wall plug over 30W.

⚠️ Never get the USB-C cable wet.

To charge:

1. Open the silicone tab on the rear.
2. Plug in the USB-C cable.
3. The speaker will chime and battery LEDs will flash in sequence.
   
   

It takes approx. 2.5 hours for a full charge with a 2.4A input.

There are 4 LEDs. Each LED = 25% charge:

🔆 Top: 75–100%

🔆 3rd: 50–75%

🔆 2nd: 25–50%

🔆 Bottom: 0–25%

Your PINE Beat can fast charge phones and tablets (not laptops).

1. Just plug in the included USB-C cable.

If charging doesn’t start: Check the port and cable for debris, clean gently, and try again.

The battery is located on the underside of PINE Beat, behind a waterproof sealed lid.

To swap batteries:

⚠️ Always flip your speaker upside down before opening to avoid dropping the battery.

1. Turn speaker upside down.
2. Slide out the recycled plastic tab lock slightly and gently push up.
3. Use your fingers on the metal edges to lift the lid either side of the lock — it may be stiff due to the seal.
4. Pull the black fabric tab to remove the battery.
5. Insert the new one.
6. Close the lid firmly — press both thumbs until the tab clicks back into place.

If you are visual, watch the video below and follow the steps.



Battery usage and safety:

⚠️ Always keep batteries dry and dirt free, they are not waterproof or IP rated.
⚠️ Do not store loose batteries in a bag etc with other metal objects.
⚠️ Do not dispose of batteries in household refuse. Batteries should only ever be disposed of at an approved re-cycling centre. Scan the QR code on the battery for recycling information.

Storage & Operating Temperature Range

• 0°C to 60°C (32°F to 140°F)
  

Tap once on the play button to play or pause.

• Single tap to skip a track.
• Press and hold until desired volume is achieved.
  

You'll hear a chime when you reach highest volume.

• Single tap to go back a track.
• Press and hold until desired volume is achieved.

You'll hear a chime when you reach lowest volume.

Press to switch through 4 sound modes in this order:
Outdoor → Extra Bass → Audiobook → Indoor

You’ll hear a different number of beeps to confirm each mode:

• 1 beep – Outdoor
• 2 beeps – Extra Bass
• 3 beeps – Audiobook
• 4 beeps – Indoor
  

Each press moves to the next mode. After 4 beeps you’ll return to Outdoor mode. 

1. Press to cycle through 3 light modes:
   White → Camp Fire Flicker → Fire → (Back to White)

Each press moves to the next mode in order. After the third press, it loops back to the beginning.

Hold for 2 seconds to turn the lights off completely. (Handy for bed time listening).

Yes, PINE Beats has a 3.5mm aux port.

1. Open the silicone tab on the back.
2. Plug in your aux cable and enjoy.

1. Power on all speakers.
   
2. Connect your phone to one of them. Make sure only one phone is connected to the speakers otherwise the Bluetooth pairing won’t work.
   
3. Double press the power button on each additional speaker.
   You’ll hear the Glacial Ice chime once they’re paired.
   

Speakers will auto-pair, keeping them very close with help with pairing. Once connected they can be a maximum distance of 20 meters of each other.

Always close the silicone charging port and battery lid before cleaning.

• Rinse with clean tap water
  
• Gently wipe with a soft microfiber or organic cotton cloth
  
• Use an air compressor to blow away sand or dirt

If anything goes wrong, don’t bin it we’ve got you:

Visit our Serving and Repair Policy

Remember your PINE Beat comes with a 30-month warranty. Explore the policy.